Frequently Asked Questions

In almost 90 years of business, we have been asked countless questions about our products and how they function. In order to help you, we have compiled a list of 30 of our most asked questions. If you find that you need further assistance, please feel free to visit our trouble shooting page for common trouble shooting questions. Contact us if you need further assistance.

All FAQ

Will these work on a gravity-flow system?

Yes. Ritchie offers different valves for different water pressure levels. Our white valve can be used for pressures between 5 and 40 PSI and is geared toward gravity-flow systems.

Can I hook this up with a hose?

Ritchie fountains are designed to be permanent installations. There are certain installations in warm climates where people will hook them up with a garden hose. Poly units with small access panels (100, 150, 150 S, 300, Omni 200) can use Ritchie part #18091, which is the small access panel with a threaded hole through it. This panel can also be used to run electricity to the unit and will accept 1” conduit. The hole is threaded 1-11 ½ NPSM.

What keeps it from tipping over?

Most poly units have molded in hold down pockets. All other units come with hold down brackets that bolt on to the unit. All units need to be anchored to a concrete pad using 3/8” stainless steel anchor bolts.

How are these installed?

A concrete pad large enough for the animals to stand on while drinking is recommended to prevent a mud-hole from forming next to the fountain. We also recommend a step to make livestock step up to the fountain and to aid with cleaning around the fountain. The easiest way to explain this is to go to the installation link on this web-site. You can also download instruction manuals to see how installation is done.

At what temperature will this freeze?

Technically, an unheated fountain will freeze at 32 degrees Fahrenheit. The amount of time that it will take to freeze depends on how well insulated the unit is, how much water is in it, and the beginning temperature of the water. Testing of a Thrifty King CT unit showed that at 20 degrees below zero Fahrenheit with a 15 mile per hour wind, the water temperature inside the unit dropped ½ degree per hour. We recommend a minimum incoming water temperature of 42 degrees Fahrenheit for Thrifty King units. Under the conditions mentioned above (42 degree source), it would take 20 hours of non-use before the water inside would freeze. Open trough fountains will freeze much faster and must be heated in freezing environments.

Why are the balls frozen on my CT unit in the morning?

In the freezing months of the year, we recommend that the float be readjusted to allow the ball closures to stay ½” below the rim of the drink well. By doing this, water does not pool around the ball, which can freeze overnight when animals are not drinking. Even when dropping the ball ½”, there is still 6” of insulation on top of the water. Other fountains cannot do this because wind will blow into the valve compartment, causing the valve to ice up. Ritchie fountain valve compartments are completely protected when doing this. In the warmer months, the float should be readjusted to allow the ball to seal.

How big of a hole do I need to get all that ground heat to keep it from freezing?

Ground heat will not keep a livestock fountain from freezing, as many of our competitors would like people to believe. This was proven during the testing performed at Iowa State University to develop the thermal tube. We recommend Ritchie thermal tubes for all installations. Thermal tubes interrupt the frost line and create an airspace around the water line. The airspace around the water line actually gets some warmth from the water that is coming up through the water line. This airspace keeps the water line from freezing. At the frost line, the air temperature around the pipe is above freezing. As you move closer to the side of the thermal tube, the air will be gradually colder and will be freezing at the side of the thermal tube. That is why the water supply line should not touch the side of the thermal tube. With no water running through the pipe the air temperature inside the thermal tube will eventually be the same temperature as the ground outside the thermal tube. This is the same principle as a thermos of coffee. In most cases, all Ritchie fountains, except Thrifty King CT units used in a correct application, will require a heating system to prevent freezing.

Do they freeze?

With correct installation, and assuming that the electricity is operating, the answer is no. If a Ritchie fountain is frozen, it is because something is defective, a poor installation, or the application is not correct. The most common cause of freezing is a heater that has burned out, or a thermostat that has failed. If it is a Thrifty King CT unit that is being used without heat, it can be a poor installation that is allowing cold air to get underneath the unit, incoming water that is below 42 degrees, or not meeting the minimum head requirements for using these units. A majority of the time when a unit is not working in cold weather, it is at the valve. The supply line touching the side of the riser tube, which causes the water to slush up and not go through the valve, usually causes this. This is seldom a problem and will not happen with correct installation.

Are these frost-free fountains?

This is one of the most frequent questions that we hear about poly units. All Ritchie fountains are frost free with the use of a heat system. We interpret frost free to mean energy free, which we then again translate to electric free. There is a misconception that because it is made of plastic it is electric free.

Will I be able to add heat to the standard Stall Fount later?

No. The standard Stall Fount is not set up for adding heat.